Difference between revisions of "StrichLux/IO-DMX"
From Hackstrich
(Dormantizing for now.) |
|||
| (5 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
== Project Status == | == Project Status == | ||
| + | * 2012-09-09: Putting on hold for now, other modules have priority. | ||
| + | * 2012-05-31: Fixed a bunch of issues introduced in the rearchitecting, transmission now works properly again. Started working on the architecture for the DMX receiver module. | ||
| + | * 2012-05-28: Rearchitected the code to support transmission or reception modules being activated via a series of muxes. | ||
| + | * 2012-05-16: If I disable the tx_en functionality, transmission now fully works! Need to troubleshoot tx_en further, and get reception done. | ||
| + | * 2012-05-01: Still not able to get it working on real hardware. Attempted to get JTAG working, found TDI/TDO pins were connected wrong, green-wired it and can now connect to the chip via JTAG. Will do more troubleshooting tomorrow. | ||
* 2012-04-29: Spent a few hours finding/fixing bugs, simulator now looks really good. Will test on real hardware this week. | * 2012-04-29: Spent a few hours finding/fixing bugs, simulator now looks really good. Will test on real hardware this week. | ||
* 2012-04-23: Worked more on the code for the CPLD, it's getting stuck somewhere in the state machine and hanging outputting a high level. Need to troubleshoot more in the simulator. | * 2012-04-23: Worked more on the code for the CPLD, it's getting stuck somewhere in the state machine and hanging outputting a high level. Need to troubleshoot more in the simulator. | ||
| Line 21: | Line 26: | ||
== Architecture == | == Architecture == | ||
| − | + | [[Image:io-dmx_architecture.png]] | |
| − | + | [[Category:Dormant Projects]] | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | [[Category: | ||
| − | |||
Latest revision as of 05:07, 9 September 2012
The StrichLux IO-DMX module will provide one universe of DMX for the StrichLux system, and can be used as either an input module or an output module.
Project Status
- 2012-09-09: Putting on hold for now, other modules have priority.
- 2012-05-31: Fixed a bunch of issues introduced in the rearchitecting, transmission now works properly again. Started working on the architecture for the DMX receiver module.
- 2012-05-28: Rearchitected the code to support transmission or reception modules being activated via a series of muxes.
- 2012-05-16: If I disable the tx_en functionality, transmission now fully works! Need to troubleshoot tx_en further, and get reception done.
- 2012-05-01: Still not able to get it working on real hardware. Attempted to get JTAG working, found TDI/TDO pins were connected wrong, green-wired it and can now connect to the chip via JTAG. Will do more troubleshooting tomorrow.
- 2012-04-29: Spent a few hours finding/fixing bugs, simulator now looks really good. Will test on real hardware this week.
- 2012-04-23: Worked more on the code for the CPLD, it's getting stuck somewhere in the state machine and hanging outputting a high level. Need to troubleshoot more in the simulator.
- 2012-04-20: Programmed CPLD and it successfully blinks the status LED green/red! Also started working on the controller code.
- 2012-04-10 - 2012-04-20: Wrote Ruby code to read JEDEC files (ruby-jedec) and program MachXO2 CPLDs via the Bus Pirate
- 2012-04-04: Wishbone interface for DMX transmitter complete, as is mux for sharing the bus between SPI and DMX. Controller is the last Verilog piece pending.
- 2012-04-03: Verilog for DMX transmitter complete and tested in simulator.
- 2012-03-17: Schematic complete and checklist checked, starting and finished board layout/routing, CAM done, submitted to Laen for PCB manufacturing. Parts still need to be ordered.
- 2012-03-15: BOM is complete, schematic almost complete.
- 2012-03-14: Started schematizing/putting BOM together.
Specs
- One universe of DMX, no RDM support at least at the beginning.
- Can be used as an input or output module.
- Based around the Lattice MachXO2-256 CPLD
Rev. 1 Issues
- TDI/TDO signals are not connected to the right pins
Architecture
