Difference between revisions of "Zappy Module"
From Hackstrich
(Adding collar output waveforms) |
|||
| Line 23: | Line 23: | ||
* May need a dump resistor if the cap is charged and needs to be discharged without zapping? | * May need a dump resistor if the cap is charged and needs to be discharged without zapping? | ||
** Could use the series charging resistor w/ a different FET to dump the cap through it? | ** Could use the series charging resistor w/ a different FET to dump the cap through it? | ||
| + | |||
| + | == Waveforms == | ||
| + | All collar output waveforms are through a 1/3 divider, so multiply by 3 to get actual amplitude | ||
| + | <gallery> | ||
| + | Image:zappymod-collar-1l.png|Collar Output - Level 1L | ||
| + | Image:zappymod-collar-2l.png|Collar Output - Level 2L | ||
| + | Image:zappymod-collar-3l.png|Collar Output - Level 3L | ||
| + | Image:zappymod-collar-4l.png|Collar Output - Level 4L | ||
| + | Image:zappymod-collar-5l.png|Collar Output - Level 5L | ||
| + | Image:zappymod-collar-6l.png|Collar Output - Level 6L | ||
| + | Image:zappymod-collar-8l.png|Collar Output - Level 8L | ||
| + | Image:zappymod-collar-1h.png|Collar Output - Level 1H | ||
| + | Image:zappymod-collar-2h.png|Collar Output - Level 2H | ||
| + | Image:zappymod-collar-3h.png|Collar Output - Level 3H | ||
| + | Image:zappymod-collar-4h.png|Collar Output - Level 4H | ||
| + | Image:zappymod-collar-5h.png|Collar Output - Level 5H | ||
| + | Image:zappymod-collar-6h.png|Collar Output - Level 6H | ||
| + | Image:zappymod-collar-7h.png|Collar Output - Level 7H | ||
| + | Image:zappymod-collar-8h.png|Collar Output - Level 8H | ||
| + | </gallery> | ||
[[Category:Current Projects]] | [[Category:Current Projects]] | ||
Revision as of 04:20, 3 February 2015
Zappy Module is a board-level module that takes control input via some kind of protocol and outputs signals to zap someone like shock collars do.
Project Status
- 2015-02-02: Started putting together overall circuit idea.
- 2015-02-01: SPICEd out some ideas.
- 2015-01-29: Captured waveforms of all output levels.
- 2015-01-05: Arranged to borrow a shock collar to characterize the output of it.
- 2013-05: Started throwing ideas around.
Overview
- Control input options could be:
- GPIO-based, simple "zap now" input (or a couple separate inputs that you can set with different options)
- I2C/SPI/RS232
- Could be used for instant control or programming levels/durations for later GPIO-based activation
Theory of Operation
- Input voltage from 3-9V is stepped up to 10V using a boost converter (AZ34063U) to get the intermediary voltage rail
- Or if 12V input is required, maybe use 14V or something as the intermediary voltage rail?
- MCU controls a FET that charges a cap from that rail via a series resistor to control charge rate
- Divider on the cap feeds into an analog pin on the MCU, once the analog pin reaches the desired level the MCU shuts the FET off again
- Once cap is charged, MCU pulses a FET that dumps the charge on the cap through a 1:100 (or so) transformer and to the output
- 0.1-1kV should be achievable via timing the charge FET
- May need a dump resistor if the cap is charged and needs to be discharged without zapping?
- Could use the series charging resistor w/ a different FET to dump the cap through it?
Waveforms
All collar output waveforms are through a 1/3 divider, so multiply by 3 to get actual amplitude
Collar Output - Level 1L
Collar Output - Level 2L
Collar Output - Level 3L
Collar Output - Level 4L
Collar Output - Level 5L
Collar Output - Level 6L
Collar Output - Level 8L
Collar Output - Level 1H
Collar Output - Level 2H
Collar Output - Level 3H
Collar Output - Level 4H
Collar Output - Level 5H
Collar Output - Level 6H
Collar Output - Level 7H
Collar Output - Level 8H
